Mykhailo Serha
Design Engineer
Experience
Design Engineer
Instytut Rolnictwa Precyzyjnego Sp. z o.o.
Robotic system for wind turbine services. Structural mechanical calculations and design. ACS design. Constructions design, Special measuring system and electronics design.
Chief Project Engineer
LOTUS LTD
Design of a mini-monoblock installation for thermocatalytic processing of used engine oils into diesel oil fraction with a capacity of 1,000 tons/year. Technological design. Chemicals and heat calculation. Construction design.
Chief Project Engineer
LOTUS LTD
Complex for processing agricultural plant waste for the production of commercial gas methane and liquid carbon dioxide with a capacity of 1,200 m3/h of methane and up to 20 t/day of liquid carbon dioxide. Full technological, chemicals, structural and construction design, heat exchange calculation. Developing and design ACS systems, special electronics and software's.
Components included:
- Fuel crushing and storage reception system
- Reactor for gasification of carbon dioxide in the gas phase in a fluidized bed
- Hydrocarbon cracking column
- Absorption-desorption installation for the release of carbon dioxide
- Carbon dioxide liquefaction installation
- Cryogenic methane rectification installation
- Auxiliary gas generator unit to power the gasification reactor and steam boilers
- Heat recovery and steam production installation with a capacity of 5 tons of steam/hour
- ACS TP system of the complex
Chief Project Engineer
LOTUS LTD
Boiler heat recovery of waste gases from the gas piston engine of a generating set with a power of 0.5 MW. Construction design, heat exchanger calculation.
Chief Project Engineer
Bio-Energy LTD
Station for measuring the parameters of the engine-generator installation. Measuring and electronics circuit and systems design.
Chief Project Engineer
LOTUS LTD
Gas generator for gasification of agricultural waste instead of natural gas used to power technological gas devices with a thermal power of 6 MW. Structural system design. Components choosing. ACS systems design. Construction design. Technological design. Chemical-heat and mechanical calculation.
Design and installation of supply voltage stabilization 200 kVA, 0.4 kV with power factor regulation. Power electronic design. Design measuring sensors and signals processing algorithms.
Gas engine for operation on low-calorie gas fuel based on the YAMZ238 engine with conversion of the engine from diesel oil to gas fuel. Structural system design. Components choosing. ACS systems design. Construction design. Technological design. Chemical-heat calculation. Developing and design special electronics and software's.
Chief Project Engineer
Bio-Energy LTD
Complete power distribution installation for paper production equipment with a dissipated power of 10 MW and a controlled electric drive system with a power of 3 MW. Structural system design. Components choosing. Construction design. Electrical, heat and mechanical calculations.
Chief Project Engineer
LOTUS LTD
Design and installation for the disposal of printed circuit boards of electronic devices with the separation of tin-lead solder in the form of an ingot, copper in the form of copper powder, separation of aluminum alloys and ferrous metals and thermal gasification of thermosetting plastics, with a raw material capacity of 2 t/day. Structural system design. Components choosing. Construction design. Electrical, heat and mechanical calculations.
Design and installation of reactive power compensation with a capacity of 1.2 MVA. Structural system design. Components choosing. Construction design. Electrical, heat and mechanical calculations.
Chief Project Engineer
LOTUS LTD
Design of a steam boiler room for solid fuels with a steam capacity of 3 tons of steam per hour. ACS systems design. Structural system design. Components choosing.
Chief Project Engineer
LOTUS LTD
Design and installation for measuring paper parameters in the production process. Structural system design. Measuring and electronics circuit and systems design.
Design and installation for drying paper fabrics with an infrared heater with gas fuel with a power of 1.5 MW. Structural system design. Components choosing. ACS systems design. Construction design. Technological design.
Design and installation of convection and conduction paper drying. Structural system design. Components choosing. ACS systems design. Construction design. Technological design.
Design and installation of ultrasonic dewatering of paper cloth during production. Construction design. Technological design. Design electronics circuit and systems.
Chief Project Engineer
LOTUS LTD
Design and installation of a closed electro-chemical-flotation circuit for the treatment of waste water from paper production. Structural system design. Components choosing. ACS systems design. Construction design. Technological design.
Chief Project Engineer
LOTUS LTD
Mini-factory for the production of sanitary paper. Development of a plant construction project. Development of a mass production project. Design special heater and burners. ACS systems design.
Chief Project Engineer
VIF LTD
Design of a steam boiler room for solid fuels with a steam capacity of 10 tons of steam per hour. Heating system design. ACS systems design.
Chief Project Engineer
Dairy Zarog LTD
Design of a treatment plant complex for a dairy plant with a capacity of up to 100 m3/day. Heating system design. Waters recovery system design.
Chief Project Engineer
Status-PAP LTD
Mini-factory for the production of sanitary paper. Heating system design. Waters recovery system design.
Chief Project Engineer
Novomoskovsk Knitting Factory NTF LTD
Design of a closed-circuit electrochemical wastewater treatment complex after the production of knitted fabrics with a capacity of up to 100 m3/day. Structural system design. Components choosing. ACS systems design. Construction design. Technological design.
Chief Project Engineer
Novomoskovsk Knitting Factory NTF LTD
Design and installation of an electrochemical wastewater treatment plant of a knitwear dyeing shop. Structural system design. Components choosing. ACS systems design. Construction design. Technological design.
Design and installation of heat utilization after steam treatment of knitwear in autoclaves with a power of 0.5 MW per body with cold production using the absorption-desorption cycle. Structural system design. Components choosing. ACS systems design. Construction design.
Chief Project Engineer
Novomoskovsk Knitting Factory NTF LTD
Design of a technological compressor-air installation with Р=0.8MPa and a capacity of 3000 m3/h with the use of excess casing in the heating system. ACS systems design. Structural system design. Components choosing.
Chief Project Engineer
Novomoskovsk Knitting Factory NTF LTD
Design of a steam boiler room with a steam capacity of 2 tons of steam per hour. ACS systems design. Structural system design. Components choosing.
Chief Project Engineer
OWEKON-SERVICE LTD
Design of a gas boiler room for a heating installation with a capacity of 0.6 MW. ACS systems design. Structural system design. Components choosing.
Chief Project Engineer
OWEKON-SERVICE LTD
Design of a knitwear production plant with a capacity of 50 million pairs per year. ACS systems design. Structural system design. Components choosing.
Design of a ventilation and air-conditioning installation for an oversized tire workshop with an area of 20,000 m2. ACS systems design. Structural system design. Components choosing.
Chief Project Engineer
MPP On Line Dniepr LTD
Projects of ventilation installations for special technological equipment. ACS systems design. Structural system design. Components choosing. Heat flow calculations.
Design of a heating, ventilation and air conditioning installation for a shopping complex with an area of 10,000 m2 in Dnipro city. ACS systems design. Structural system design. Components choosing.
ACS TP Engineer
Teploenergonaladka LTD
Design of a control system for steam boilers in coke chemical production plants. ACS systems design. Heat equilibrium calculations.
Electronics Engineer
Koloryt LTD
Plasmatron power supply module for the non-fire plasma chemical treatment of steel system. Power electronic design. Design measuring sensors and signals processing algorithms.
Chief Project Engineer
Innomedyka LTD
Packing - packaging line. ACS systems design. Mechanical drivers design. Construction design.
ACS TP Engineer
Innomedyka LTD
Mini-factory for the production of perfumes and cosmetics. ACS systems design.
Electronics Engineer
Wesna-Komplekt LTD
Underground radio communication and emergency notification system Vesna NSh-3M complex. Developing and design electronics circuit and systems, signals processing algorithms.
Underground radio communication and emergency notification system Vesna NSh-3 complex. Developing and design electronics circuit and systems, signals processing algorithms.
Non-destructive Testing Engineer
Przedsiębiorstwo Produkcyjno-Handlowe Stalprom LTD & Physico-Technical Institute of Dnipropetrovsk National University
Electromagnetic-acoustic control system for railway wheels. Developing and design electronics circuit and systems, signals processing algorithms.
Ultrasonic control system for aircraft tire cord delamination. Developing and design electronics circuit and systems, signals processing algorithms.
Design and installation of X-ray structural analysis of pipe welding seams for ongoing inspection. Developing and design electronics circuit and systems, signals processing algorithms.
Non-destructive ultrasonic inspection system for boiler tubes. Developing and design electronics circuit and systems.